Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Do not undervalue the forklift at the office. If the operation is bad, there will certainly be major mishaps in mins, and there are several accidents entailing forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the person ahead might not be found, resulting in a moving accident.
Instance 2: In order to keep the balance of the forklift when lifting heavy goods, the staff members utilized their body weight as the counterweight, which virtually caused casualties.
Case 3: The width of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which nearly causes an mishap.
Case 4: Forklift is speeding up and surrender throughout a turn.
Instance 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the safety belt, the forklift lifter falls and the vehicle driver is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the lorry when it rolled over and was squashed.
Forklift procedure must pay attention to these matters ：.

Start.
1. Prior to starting, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, honk the horn initially and after that start.
2. For automobiles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge must be safe before beginning.
3. When the forklift begins with a lots, the chauffeur must first verify that the load is secure and dependable.
4. The start should be slow and stable.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the pole ought to be slanted in reverse. .
2. Do not raise the fork expensive when driving. When getting in and leaving the work site or while driving, be careful that there will certainly be no barriers in the sky. When the load is taking a trip, the fork should not be elevated expensive, which will certainly affect the security of the forklift. .
3. After unloading, the fork must be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal ought to be released initially. High-speed doglegs are restricted. High-speed sharp turns will trigger the automobile to lose side security and topple. .
5. When the forklift is downhill, it is purely prohibited to turn off the fire and slide, and it is forbidden to brake suddenly while driving with lots unless there are special conditions.
6. When the forklift is running, it needs to obey the traffic rules in the manufacturing facility and need to maintain a particular security distance from the lorry in front. .
7. When the forklift is running, the tons has to be in the lowest placement that does not impede the driving, and the gantry needs to be properly tilted back. The load shall not be increased except when piling or loading. .
8. The height of the load must not obstruct the driver's sight. In unique scenarios, when the thing influences the forward vision, drive at a low speed when reversing.
9. It is forbidden to switch on the ramp, neither to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it needs to drive safely at a reduced rate when going into the manufacturing workshop location. .
11. When the forklift is raised, raised or driven, it is restricted for employees to depend on the fork to hold things and play a stabilizing duty. .
12. If problems are found, they will certainly be repaired and reported in a timely manner, and they will never ever operate with ailments or hide them.

filling and unloading.
1. When fork-loading things, the range between the two forks ought to be readjusted as needed to make the load of the two forks well balanced and not manipulated, and one side of the product ought to protest the rack. .
2. It is forbidden to work with a solitary fork or utilize a fork top or draw. In unique scenarios, security warning signs must be established to remind bordering pedestrians. .
3. In the process of packing and dumping items, the forklift needs to be stopped with the brake. .
4. The speed of the automobile need to be sluggish and constant. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork ought to be as deep as possible under the load, and it must be kept in mind that the fork suggestion need to Stand-on Electric Pallet Stacker not touch other goods or items. The tons needs to be stabilized with minimal back tilt of the gantry to make sure that the tons does not move in reverse. The mast can be tilted forward slightly when the tons is decreased to enable easy placement of the load and removal of the forks. .
6. It is prohibited to fork products at broadband and hit tough things with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to loaf the fork, so as to avoid the collapse of the goods and hurt individuals. .
8. Overwhelming is restricted, and it is prohibited to use forks to raise employees to take part in high-altitude procedures to stay clear of high-altitude dropping mishaps. .
9. It is not allowed to use the brake inertia to slip, place, round or roll objects. .
10. It is not allowed to utilize forks to pick, turn pallet dump.

Leaving .
1. It is restricted to leave the forklift when the items on the fork impend. Prior to leaving the forklift, you have to discharge the goods or reduced the fork structure.
2. Pull the emergency brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be checked, and gas, lubing oil and cooling water should be included.
2. Examine the security performance of starting, running and braking.
3. Inspect whether the lights and horn signals are complete and reliable.
4. During the operation of the forklift, examine whether the stress and temperature level are regular.
5. After the forklift is running, the external leak must additionally be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the vehicle;.
2. When you run into someone in front of you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the low point of the freight need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be too sharp to prevent the propensity of "free switching";.
6. Running up and down the slope needs to be slow and consistent, and no turning on the incline is permitted.
7. Do not drive across the slope. When the gradient is above 10%, the lorry must be driven in reverse when worsening;.
8. When the forklift workers lug the goods and progress, if they encounter huge or heavy goods and go to the motorist's line of vision, they must take the turning around workout
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork procedure is not permitted.
2. It is not permitted to lift the goods for long distance driving.
3. It is not permitted to grab the goods by passing on the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other harmful chemicals with forks.
5. It is not enabled to use inertia pressure to get the goods.
6. It is not permitted to use stopping force to exile round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or Stand-on Electric Pallet Stacker fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the following conditions.
1. Contours, slim roads, train crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844